FAQFAQ SearchSearch MemberlistMemberlist  RegisterRegister  ProfileProfile Log in to check your private messagesP.M. Log inLog in
Motor rebuild program

 
Post new topic   Reply to topic    OFNA Nitro Talk Back Forum Forum Index -> Positive OFNA Feedback
View previous topic :: View next topic  

Author Message
bpoates25



Joined: 06 Jun 2008
Posts: 212

PostPosted: Fri Nov 14, 2008 9:02 pm    Post subject: Motor rebuild program Reply with quote

Just want to say thanks to DJ for getting in touch with me about my broken Force 28, and explaining the motor rebuild program. Needless to say, my motor is on the way. Thanks Ofna for having this program to help your customers out. Great job, and you have a customer for life. As I said on the RC Universe forum. Ofna is on the ball. Thanks again.
Back to top
View user's profile Send private message
Author Message
biggame



Joined: 19 Nov 2008
Posts: 4

PostPosted: Wed Nov 19, 2008 8:38 am    Post subject: Reply with quote

Can someone contact me about the motor rebuild program. I have a Hyper 8 Port Race engine. The bearing is leaking in front, it runs great until it gets up to 190 and then won't idle. Runs fine as long as I hold the gas down. I heard that the program will replace the piston, sleve and crank. What would it cost for bearings and a possible new con rod too. It deosn't have more than 4-5 gallons through it. Please email me @ jamesdcurry@verizon.net with the price and instructions on where to send it.

Thanks. James Curry
Back to top
View user's profile Send private message
Author Message
MX250



Joined: 12 Nov 2005
Posts: 1340
Location: Monroe,GA

PostPosted: Wed Nov 19, 2008 6:17 pm    Post subject: Reply with quote

the you can do the bearings your selt, the TKO ceramic bearings are great... but if you want the engine rebuilt piston/con rod/sleeve ofna should be able to help you for no more than $65.00
Back to top
View user's profile Send private message
Author Message
bpoates25



Joined: 06 Jun 2008
Posts: 212

PostPosted: Thu Nov 20, 2008 8:26 am    Post subject: Reply with quote

Hey Biggame,

You may just want to go over to the Ofna site, and shoot DJ, Dave, or Roger a message. They may get it faster than on the forum? Anyway, good luck.
Back to top
View user's profile Send private message
Author Message
DJ



Joined: 22 Jun 2006
Posts: 979

PostPosted: Thu Nov 20, 2008 8:34 am    Post subject: Reply with quote

The rebuild would only consist of the pis/slv and connecting rod on the Hyper engines, if your bearing and crank is bad we would not be able to rebuild that engine to guarantee the rebuild work.
Back to top
View user's profile Send private message
Author Message
socalbash



Joined: 20 Oct 2005
Posts: 2803

PostPosted: Thu Nov 20, 2008 2:51 pm    Post subject: Reply with quote

whats the Hyper 8 port rebuild cost for P/s/con rod?

TIA,

SOCAL

glad this program hasnt been terminated :-)
Back to top
View user's profile Send private message
Author Message
DJ



Joined: 22 Jun 2006
Posts: 979

PostPosted: Fri Nov 21, 2008 2:17 pm    Post subject: Reply with quote

That's $65.00 but it's only pis/slv/connecting rod, this engine does not have a full rebuild in any way.
Back to top
View user's profile Send private message
Author Message
c0mrade



Joined: 02 May 2009
Posts: 32
Location: Nashville,TN

PostPosted: Sun May 03, 2009 3:40 pm    Post subject: Engine Manual 4 rebuilding ???... Reply with quote

Cant you just get an engine manual to rebuild it yourself???...
i heard somewhere i think it was on these forums that theres a engine manual...
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    OFNA Nitro Talk Back Forum Forum Index -> Positive OFNA Feedback All times are GMT - 9 Hours
Page 1 of 1
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
ofna nitro talk back