 |
 |
|
 |
|
| Author |
Message |
VWVR6_T
Joined: 23 Aug 2009
Posts: 384
Location: Western, PA
|
 Posted: Sun Mar 28, 2010 9:39 am Post subject: |
 |
|
| If you are getting 240 at 50 deg, once the weather change you do have to change the tune according to outside temps. Everytime you change something in the engine you do have to re-tune, either fuel,pipe,gearing, etc. |
|
| Back to top |
|
|
|
 |
|
 |
|
|
|
|
| Author |
Message |
nitro_79
Joined: 24 Mar 2010
Posts: 18
Location: Indianapolis, Indiana
|
| Posted: Sun Mar 28, 2010 11:31 am Post subject: |
|
|
| yep, the fun of nitro. I went a head and pulled it apart. I've got a couple other things apart and am replacing my radio so I thought it would be a good time to down the revo. Pulled the picco apart, like I said before looks good, did notice that I could see light through the front bearing seal so I guess I could have been getting air through there. I ordered a new boca ceramic for the front. I will say that this thing is tight, the tolerances are very very tight. the crank fits real snug in the bearings, very well built wouldn't expect anything less from them. I will repost once I get my new bearing installed and also ordered some of the lucky 7 air seal I'll give that a shot. Thanks for the advise, hope I can get it back together by Friday. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
| Author |
Message |
VWVR6_T
Joined: 23 Aug 2009
Posts: 384
Location: Western, PA
|
| Posted: Sun Mar 28, 2010 1:18 pm Post subject: |
|
|
COOL   |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
| Author |
Message |
nitro_79
Joined: 24 Mar 2010
Posts: 18
Location: Indianapolis, Indiana
|
| Posted: Thu Apr 01, 2010 4:11 pm Post subject: |
|
|
| got the new boca front bearing installed, ya know they get easier after a few engines. this one wasn't that bad but I've had some difficult ones to change bearings. the lucky 7 air seal worked great, all new orings, just waiting on my new DX3S rx so I can fire it up. I will repost once I get it up and running. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
| Author |
Message |
nitro_79
Joined: 24 Mar 2010
Posts: 18
Location: Indianapolis, Indiana
|
| Posted: Wed Apr 14, 2010 2:31 pm Post subject: |
|
|
| got her out today and was tunning, It does run better, I am down to 2 1/2 HSN and I've got a few seconds of run time on the LSN with pinch test. It runs good lots of smoke, but just doesn't have any punch through 1st gear, it hits 2nd hard. Just seems like it slowly goes through 1st gear, I would say that I would need to lean the LSN to get more low end punch, but I'm starting to see 260-270 temps, and honestly it doesn't start to run good until I get in the 240-250 range. It fires right up even after its hot, and doesn't run all erratic like its getting lean. I'm not sure but I think I'm going to get a new plug and some new fuel and see what happens. If no change then I'll shim it and go with 30% and see what happens. |
|
| Back to top |
|
|
|
|
|
|
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
|
|
|
|
FAQ 
Search 
Memberlist
Register
Profile 
P.M. 
Log in
